Built -up roof - A roofing composed of three to five layers of asphalt felt laminated with coal tar, pitch, or asphalt. The top is finished with crushed slag or gravel. Generally used on flat or low -pitched roofs.
Collar beam - Nominal 1 - or 2 -inch -thick members connecting opposite roof rafters. They serve to stiffen the roof structure.
Delamination - Separation of the plies in a panel due to failure of the adhesive. Usually caused by excessive moisture.
Frieze - In house construction a horizontal member connecting the top of the siding with the soffit of the cornice.
R Value - A measure of insulation. A measure of a materials resistance to the passage of heat. The higher the R value, the more insulating "power" it has. For example, typical new home's walls are usually insulated with 4" of batt insulation with an R value of R -13, and a ceiling insulation of R -30.
Ridge - The horizontal line at the junction of the top edges of two sloping roof surfaces.
Wall out - When a painter pray paints the interior of a home.
Yoke - The location where a home's water meter is sometimes installed between two copper pipes, and located in the water meter pit in the yard.
End "3 4 x 27 drill" research and recommendations
Cleveland 2740 Carbide-Tipped-Long-Length Drill Bit, Uncoated(Bright), Morse Taper Shank, 27/32" Dia. x 10-3/4" Lg, (Pack of 1)Feature: ... With 30 degree helix; Carbide-tipped tools feature cutting edges of carbide for wear resistance and a steel shank for toughness; Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications; Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters; When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging ...more
Editorial Reviews — ... Product Description | Greenfield Industries is a leading manufacturer of expendable cutting tools and related products. The company sells thousands of products under the brand names Cleveland, Chicago-Latrobe, Cle-Line, Vermont Tap & Die, Bassett, and Putnam Tools, Geometric, Vers-O-Tool, H & G, and Acme-Fette. The product lines include drills, end mills, taps, dies, reamers, countersinks, counterbores, tool bits, and more. These tools are used in a variety of applications, If it's being drilled, cut, bored,...more
Cleveland 2480 High-Speed Steel-Long-Length Drill Bit, Black Oxide, Morse Taper Shank, 27/32" Dia. x 10-3/4" Lg, (Pack of 1)
Feature: ... With 38 degree helix; High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance; Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge; Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters; When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging ...more
Editorial Reviews — ... Product Description | Greenfield Industries is a leading manufacturer of expendable cutting tools and related products. The company sells thousands of products under the brand names Cleveland, Chicago-Latrobe, Cle-Line, Vermont Tap & Die, Bassett, and Putnam Tools, Geometric, Vers-O-Tool, H & G, and Acme-Fette. The product lines include drills, end mills, taps, dies, reamers, countersinks, counterbores, tool bits, and more. These tools are used in a variety of applications, If it's being drilled, cut, bored,...more
Cleveland 2412 Oversized High-Speed Steel Long-Length Drill Bit, Black Oxide, Morse Taper Shank, 27/64" Dia. x 7-3/4" Lg, (Pack of 1)
Feature: ... With 30 degree helix; With 135 degree drill point, allowing for a cleaner drill hole and less slippage when starting; High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance; Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge; Morse taper shank allows the tool to be inserted directly into the machine's spindle to facilitate high-torque applications such as large cut diameters ...more
Editorial Reviews — ... Product Description | Greenfield Industries is a leading manufacturer of expendable cutting tools and related products. The company sells thousands of products under the brand names Cleveland, Chicago-Latrobe, Cle-Line, Vermont Tap & Die, Bassett, and Putnam Tools, Geometric, Vers-O-Tool, H & G, and Acme-Fette. The product lines include drills, end mills, taps, dies, reamers, countersinks, counterbores, tool bits, and more. These tools are used in a variety of applications, If it's being drilled, cut, bored,...more
End "3 4 x 27 drill" resources and offers